In diesem Artikel wird das Entfernen der hinteren Abdeckung der folgenden Geräte beschrieben:
Der Outdoor 4
This article describes how to remove the back cover of the Outdoor 4 and replace the batteries.
*The Outdoor 4 can be powered through its USB-C port using a weather resistant USB-C adapter; however, once the USB port cover is removed, the camera is no longer weather-resistant until it's reinserted.
How to remove the back cover
To remove the back cover of your camera, use the included right angle/adapter opening tool or large screwdriver.
1. Turn the screw to the left (counterclockwise) until it rotates freely.
2. Use the right angle/adapter opening tool to gently pry in one direction, lifting the back cover.
How to install your batteries
Once your back cover is removed, insert your batteries with the positive (+) and negative (-) poles aligned within the battery compartment.
Note: Blink cameras are only compatible with size AA 1.5 volt Lithium non-rechargeable batteries.
How to replace the back cover
To make sure the back cover is placed correctly, a post is included in its design. The back cover only fits when the post is aligned with the key hole on the camera.
1. Align the back cover's post with the key hole next to the camera's USB port and push to close.
2. Use the right angle/adapter opening tool, a coin, or large screwdriver to turn the screw to the right (clockwise) about three turns until the back cover is flush with the camera.
Blink Video Doorbell
This article describes how to remove the back cover and install batteries for the Blink Video Doorbell.
Release key
To remove the doorbell from its mounting plate, use the release key that came taped to the paper template in the product box.
If you need another key, contact Blink support.
Disconnecting from the mounting plate
To disconnect the doorbell from its mounting plate, press the key straight into the slot on the bottom of the unit until the gray catch is released. This will allow you to pull the doorbell off the mounting plate.
Accessing the battery compartment
Remove the battery cover
After disconnecting the doorbell from its mounting plate, remove the weather-resistant back cover to access the batteries.
Open battery cover
Flip the doorbell over so you're looking at the back. With your fingernail, lift the bottom edge of the gray latch at the bottom of the doorbell. This releases the weather-resistant cover, allowing you to remove and replace the batteries.
Note: Keep the cover in a safe place when you change batteries.
How to close the battery cover
- Insert the tabs at the top of the door into the slots near terminal screws.
- Push the bottom of the back cover until you see and hear the gray latch click into place.
Remounting the doorbell
Align the top of the doorbell with the top of the back plate so that the hook sets. Next, press the bottom against the back plate firmly until you feel and hear a click.
After you've remounted your doorbell, press the doorbell button to test it.
Video Doorbell with 2-hole back plate
Disconnecting from the mounting plate
If your doorbell has an open battery compartment, the latch is opened by pulling the release key toward you slightly. When released, slide the doorbell up while pivoting away from the mounting plate.
Accessing the battery compartment
Once you've dismounted the doorbell, flip the camera over and replace the batteries as needed.
Reinstalling the doorbell
Connect the doorbell to its mounting plate by lining up the pins and using a two step motion - press the doorbell against the back plate firmly (with moderate force), then push down to line up the bottom edges. You should feel a slight click when the doorbell is secure.
After you've reinstalled your doorbell, press the doorbell button to test it.
DeleteOutdoor und Indoor (3rd Gen)
Use this article for instructions on how to remove the back cover and install batteries for Blink Outdoor and Indoor (3rd Gen) cameras.
Before you begin
Before attempting to remove the back cover, make sure the camera is disconnected from any mounts or accessories. This includes any third-party products it may be attached to.
If the camera is brand new, a plastic sticker on the back of the camera shows the direction to turn. Peel off this sticker before using the camera.
To remove the back cover and open the camera
- If it is present, remove the silicone protective cover from the fastening screw, and keep it for future use.
- Use the included opening tool to turn the screw counter-clockwise (turning to the left) until the screw rotates freely. If the tool isn't available, an equivalent object such as a coin or a flat head screwdriver can also be used.
- With the tool inserted into the slot, apply side pressure on the tool and gently pry the cover loose. As shown in the illustration, hold the camera on its side with one hand while you pull with the other hand.
Optional instructions: There is another way to remove the back cover.
- After the screw has been unscrewed completely, flip the opening tool around and insert the mounting end into the camera's back cover hole. You will feel and hear a click when the tool is secured.
- Hold the camera with one hand and pull the opening tool gently backwards. This will allow the back cover to come off.
Install or replace batteries
Once the back cover has been removed, you will have access to the battery compartment. Add or replace the 2 AA lithium batteries into their slots, matching up the + and - that's labeled on the camera with the + and - labeled on the batteries.
Replace and secure the back cover
- Align the guide notches as shown, and press the cover back in place against the camera body.
- Hand tighten the screw clockwise (turning to the right) until snug. Take care to prevent over-tightening. The cover should be flush with the camera body when you are done.
XT2 und XT
In diesem Artikel erfahren Sie, wie Sie die Batterieabdeckung von Ihrer neuen Blink XT -Kamera entfernen. Sie können sich auch ein Video zum Entfernen ansehen, indem Sie hier klicken.
1. Halten Sie die Kamera so, dass die Rückseite zu Ihnen zeigt.
2. Sie werden einen grauen Schalter mit einem Pfeil bemerken, der zur Unterseite der Kamera zeigt. Schieben und halten Sie es in Pfeilrichtung.
3. Ziehen Sie dabei mit dem Daumen den Batteriedeckel nach oben. Dies kann etwas Kraft erfordern, da die Kamera luftdicht ist.
4. Heben Sie die Batterieabdeckung von der Kamera ab.
Jetzt können Sie die Batterien einlegen und auf die Geräteseriennummer (DSN) Ihrer Kamera zugreifen.
Indoor (Gen 1)
Der Riegel zum Entfernen der hinteren Abdeckung der Indoor (Gen 1) befindet sich an der Unterseite. Schieben Sie den Riegel, um die Batterieabdeckung zu lösen.
Klicken Sie hier, um zu erfahren, wie Sie die Batterieabdeckung von der Blink Indoor und Outdoor Kamera entfernen.
Der Blink Mini benötigt keine Batterien.