Support Home Battery Doorbell 2K+ Using the Battery Doorbell 2K+

Installing and Mounting Your Battery Doorbell 2K+

 Important: Complete the doorbell setup process in the Blink app before proceeding with installation.

Getting started

To complete the installation, you will need:
  • Hardware: Included mounting screws and wall anchors.
  • Power tools: Electric drill along with two drill bits, the bit size depends on your installation surface:
    • 3/32-inch (2.375 mm) bit: For drilling pilot holes for screws when installing on wood or softer surfaces.
    • 7/32-inch (5.41 mm) bit: For drilling holes for wall anchors when installing on brick, stucco, concrete, or drywall requiring anchors.
  • Basic tools: Phillips-head screwdriver and adhesive tape for securing the paper template provided in your kit.

Before you proceed with the installation and mounting process, review the following:

  • Ensure setup is complete: Your doorbell must be set up in the Blink app before mounting.
  • Identify a mounting location: Choose a location 40-48 inches (102-122 cm) above the floor.
  • Clean the mounting surface: This will ensure a secure installation.
  • Gather your materials: Have all hardware and tools ready.

Installing and mounting your doorbell 

The Battery Doorbell 2K+ camera points straight out from the included mount. For installation on uneven or small surfaces, you should only use the top and bottom mounting holes. When using all mounting holes, be careful not to over-tighten the middle screw. While a gap between the back plate and doorbell won't affect performance, you can try slightly loosening the middle screw to eliminate any gaps that may appear.

If the included mount doesn't provide the desired viewing angle, consider two alternative mounts (sold separately) that offer additional adjustment options: 

  • Corner Mount: If you need to adjust the horizontal angle, the mount offers a 25° tilt to the left or right.
  • Wedge Mount: If you need to adjust the vertical angle, the mount provides a 5° vertical tilt, allowing you to tilt the camera slightly up or down.

These mounting accessories can help you optimize the camera's field of view for your specific installation location. Choose the appropriate mount based on whether you need to adjust the vertical or horizontal angle of your doorbell camera.

For optimal installation, below you'll find step-by-step instructions for each mounting option:

Non-wired installation

Risk of electrical shock: Working with electrical components carries a risk of shock. If you cannot verify your transformer's specifications or are unsure about installation, please consult a licensed professional.

To mount your Battery Doorbell 2K+ follow these steps in the Blink app: 

  1. From the Home Screen, tap the More (...) button on your Battery Doorbell 2K+ thumbnail.
  2. Tap Device Settings.
  3. Tap Doorbell and Chime Settings.
  4. Tap Mounting and Chime Setup.
  5. Tap Mount Doorbell and follow the instructions.

If you selected No to wire your doorbell to your existing chime box, follow these steps to continue with the non-wired installation:

Mounting the Battery Doorbell 2K+ in place of an existing doorbell

Tap Yes if you are mounting the Battery Doorbell 2K+ in place of an existing doorbell and follow these steps:
  1. Turn off power to your existing doorbell and chime box. Tap Continue. 
  2. Remove your existing doorbell. Tap Continue.
  3. Screw on the wire caps (provided in your kit) to the wires from your existing doorbell and tuck them into the wall. Keep the wires separate.
  4. Switch the power back on. Tap Continue.

If using a wedge or corner mount

Tap Yes to install the wedge or corner mount.

  1. Assemble the mount to create the desired camera angle. Mount the bracket 40-48 inches (102-122 cm) above the floor or where your previous doorbell was located, drill through the mounting slots, and use the screws, and anchors (included in your package) to secure it. Tap Continue.
  2. Attach and screw the back plate onto the mount. Tap Continue.
  3. Attach and secure your Battery Doorbell 2K+ onto the back plate. Tap Continue.
  4. The Battery Doorbell 2K+ will search for a Wi-Fi connection. When connected, tap Done. If a timeout message appears, try again.
Your installation is complete. 

If not using a wedge or corner mount

Tap No if you are not using a wedge or corner adapter.
  1. Tape the drill template (included in your package) 40-48 inches (102-122 cm) above the floor or where your previous doorbell was located. Tap Continue.
  2. Drill a hole at the top and bottom indicated positions on your template. For mounting on brick, stucco, or drywall-type materials, use the included white plastic wall anchors, which fit the hole from a 7/32-inch (5.41 mm) drill bit. Tap Continue.
  3. Remove the drill template. Attach one wire to each screw on the back plate. Either wire can be connected to either post. Use the provided wire extensions and wire nuts, if necessary. Tap Continue.
  4. Align the back plate with the holes on your surface and use the provided screws to secure the plate to the wall (do not overtighten). Tap Continue.
  5. Attach and secure your Battery Doorbell 2K+ onto the back plate. Tap Continue.

Your mounting is complete. 

Not mounting the Battery Doorbell 2K+ in place of an existing doorbell

Tap No if you are not mounting the Battery Doorbell 2K+ in place of an existing doorbell and follow these steps:
  1. Tap Yes to install the wedge or corner mount. Assemble the mount to create the desired camera angle. Mount the bracket 40-48 inches (102-122 cm) above the floor or where your previous doorbell was located, drill through the mounting slots, and use the screws (included in your package) to secure it. Make sure the wires are accessible through the opening in the bracket. Tap Continue.
    1. Attach and screw the back plate onto the mount. Tap Continue.
    2. Attach and secure your Battery Doorbell 2K+ onto the back plate. Tap Continue to complete the installation.
  2. Tap No if you are not using a wedge or corner adapter.
    1. Tape the drill template included in your package 40-48 inches (102-122 cm) above the floor or where your previous doorbell was located.
    2. Drill a hole at the top and bottom indicated positions on your template. Only use the middle hole for uneven or small surfaces. For mounting on brick, stucco, or drywall-type materials, use the included white plastic wall anchors, which fit the hole from a 7/32-inch (5.41 mm) drill bit.
    3. Attach the back plate to your surface using two screws provided in your kit and do not overtighten. To adjust, remove the Battery Doorbell 2K+ with the included key and loosen bottom screws.  
      • For flat surfaces: Use top and bottom screws.
      • For uneven surfaces: Use top and middle screws. A gap between the doorbell and back plate will not impact weather resistance. 
    4. Attach and secure your Battery Doorbell 2K+ onto the back plate. Tap Continue.
    5. The Battery Doorbell 2K+ will search for a Wi-Fi connection. When connected, tap Done. If a timeout message appears, try again.

Your mounting is complete. 

Delete

Wired installation

Risk of electrical shock: Working with electrical components carries a risk of shock. If you cannot verify your transformer's specifications or are unsure about installation, please consult a licensed professional.

When choosing wired installation, Battery Doorbell 2K+ requires a power supply between 8 - 24 volts, AC at 50 - 60Hz, and 40VA maximum. Ensure the voltage coming from the transformer matches the voltage of the chime. For example, a 16V chime should be wired to a 16V transformer. To locate your transformer, check near the main electrical panel or inside the doorbell chime housing. The voltage and VA ratings are typically printed on the transformer's label.

To mount your Battery Doorbell 2K+ follow these steps in the Blink app: 

  1. From the Home Screen, tap the More (...) button on your Video Doorbell thumbnail.
  2. Tap Device Settings.
  3. Tap Doorbell and Chime Settings.
  4. Tap Mounting and Chime Setup.
  5. Tap Mount Doorbell and follow the instructions.

If you selected Yes to wire your doorbell to your existing chime box, follow these steps to continue with the wired installation:

  1. Tap My transformer is compatible to confirm your doorbell transformer meets the requirement, and then tap Agree and Continue.
  2. Turn off power to your doorbell and chime box. Tap Continue. 
  3. Remove your existing doorbell. Tap Continue.

For wedge or corner mount installation:

If using a wedge or corner mount

Tap Yes to install the wedge or corner mount.

  1. Assemble the mount to create the desired camera angle. Mount the bracket 40-48 inches high on the doorframe, drill through the mounting slots, and use the screws, and anchors (included in your package) to secure it. Make sure the wires are accessible through the opening in the bracket. Tap Continue.
  2. Connect one doorbell wire to each screw on the back plate. Either wire can be connected to either post. Tap Continue.
  3. Attach and screw the back plate onto the mount. Tap Continue.
  4. Attach and secure your Battery Doorbell 2K+ onto the back plate. Tap Continue.
  5. Switch the power back on. Tap Continue. 
  6. The Battery Doorbell 2K+ will search for a Wi-Fi connection. When connected, tap Done. If a timeout message appears, try again.
Your installation is complete. 

If not using a wedge or corner mount

Tap No if you are not using a wedge or corner adapter.
  1. Tape the drill template (included in your package) 40-48 inches (102-122 cm) above the floor or where your previous doorbell was located. Tap Continue.
  2. Drill a hole at the top and bottom indicated positions on your template. For mounting on brick, stucco, or drywall-type materials, use the included white plastic wall anchors, which fit the hole from a 7/32-inch (5.41 mm) drill bit. Tap Continue.
  3. Remove the drill template. Attach one wire to each screw on the back plate. Either wire can be connected to either post. Use the provided wire extensions and wire nuts, if necessary. Tap Continue.
  4. Align the back plate with the holes on your surface and use the provided screws to secure the plate to the wall (do not overtighten). Tap Continue.
  5. Attach and secure your Battery Doorbell 2K+ onto the back plate. Tap Continue.
  6. Switch the power back on. Tap Continue. 
  7. The Battery Doorbell 2K+ will search for a Wi-Fi connection. When connected, tap Done. If a timeout message appears, try again.

Your mounting is complete. 

Delete

Chime options

In addition to compatible mechanical or digital chime wiring, you can use an existing or purchase a compatible digital chime like the Blink Mini camera or Blink Chime (sold separately).

For Alexa-enabled devices, you can play the doorbell sound through your smart speakers. Visit Alexa Doorbell Notifications for setup instructions.

Troubleshooting connection issues

If you experience connection problems during setup:

  1. Verify power is restored to the doorbell circuit.
  2. Check that all wire connections are secure.
  3. Ensure the Battery Doorbell 2K+ is properly seated on the back plate.
  4. Try the setup process again in the Blink app.

For additional assistance, visit Battery Doorbell 2K+ Troubleshooting.

Related articles:


Can’t find what you’re looking for?

Contact Support