Support Home Frontier XR+ Getting Started

Frontier XR+ Setup Guide

Getting started

If you're new to Blink, download the Blink app and create your account. Once you have completed these steps, you can proceed with setting up your Frontier XR+.

Frontier XR+ requires a Sync Module to function, and it is compatible with all versions of Blink Sync Modules. However, a Sync Module XR or Sync Module XR+ is required to achieve the camera's extended range capabilities. Before setting up your camera, ensure you have a Sync Module connected to your account. If you don't, refer to the steps below:

Setting up a Sync Module

If you are replacing a Sync Module with a new one, refer to replacing your existing Sync Module.

If setting up multiple cameras and Sync Modules, place each Sync Module in a separate room with at least one wall between them.

Plug in your Sync Module.
From the Blink app Home Screen, tap the plus + icon in the upper-right corner.
Tap Sync Module.
Scan the QR code on the back of the device or tap Enter Serial Manually.
Choose an existing system or create a new one with a unique name, then tap Continue.
When the Sync Module displays a blinking blue and solid green LED, tap Discover Device.
- If a different light pattern is displayed, refer to Understanding Sync Module LED Lights for troubleshooting steps.
When prompted, tap Join / Connect to join the temporary Wi-Fi network 'BLINK-[PASSWORD].'
Select your local Wi-Fi network, enter the password, and tap Join. If needed, wait for firmware updates.
- If your network doesn't appear, tap Refresh List.
When setup is complete, tap Done.

If you experience any setup issues, visit our Sync Module Troubleshooting.

Delete

Setting up your Frontier XR+

Once your Sync Module is added, you can proceed with setting up your Frontier XR+ in the Blink app.

From the Blink app Home Screen, tap the + icon in the upper-right corner.
Select Wireless Cameras.
During setup, be sure to keep your new wireless camera in the same room as your Sync Module (within 7 feet/2.13 meters). Tap Continue.
Use the provided angle adapter tool to unscrew the center (turn counter-clockwise) and remove the camera's back cover. Tap Continue.
Install the four included Energizer Lithium AA (non-rechargeable) batteries, making sure to align them with the + and - symbols marked inside. Tap Continue.
Locate the QR code and device serial number (DSN) on the back of the camera (between the battery compartments, behind the back panel) and tap Scan QR Code. Scan the QR code or tap Enter Serial Manually to enter the device serial number.
Choose a system for your Frontier XR+ camera that includes a Sync Module and tap Continue.
Your system must be disarmed to add your camera. If your system is armed, tap Disarm when prompted.
When the LED lights blink red on the front of your camera, tap Discover Device.
If the LED does not blink red after 30 seconds, try replacing the batteries.
Your camera may need a firmware update, which takes a few moments. Once you see a message confirming the camera has been added, tap Continue.
Name your camera by selecting a default option, or tap Custom to enter a unique name.
On the Network Selection screen, the app will perform a site scan to evaluate signal strength, stability, latency, bandwidth, and congestion. This scan can take up to 1 minute to complete and can be backgrounded in the app. Review the recommended settings (resolution and XR mode) and tap Confirm.
Resolution options: Saver (720p/15fps), Standard (1080p/24fps), or Best (2K/24fps).
On the Settings Presets screen, choose the option that works best for you and tap Confirm Preset.
Tap Done to complete setup, or tap Mounting information if you need help mounting your camera now. To mount your camera later, refer to Mounting your Frontier XR+ when ready.
Replace the back cover of your camera by turning the screw clockwise (right) three times using the right-angle adapter, coin, or large screwdriver until the back cover sits flush with the camera.

Note: The silicone plug covering the USB-C port must always be covered in order for your camera to be weather-resistant.

Mounting your Frontier XR+

Blink Frontier XR+ camera offers a variety of mounting options. You can install it on walls, ceilings, or flat surfaces to find the best view of your area.

Mounting instructions

Your Frontier XR+ camera includes:

1 standard mounting bracket
1 opening tool/right-angle adapter
Two mounting screws

Camera placement

Position the camera within range of the Sync Module. Mount up to 10 feet (3 meters) high, aimed at your target area. Side-to-side movement across the camera's field of view is most easily detected, so position the camera where motion will cross the frame rather than move directly toward it.

To learn more, visit Blink Camera Placement Guidelines.

Wall mounting

Attach the mounting plate to the wall by following these steps:

Using the provided screws and wall anchors, attach the mounting plate to the wall.
Once the base is secured, press the Frontier XR+ camera onto the mounting point until it clicks into place.
Adjust the camera angle by gently swiveling it on the mount to aim at your target area.

Ceiling mounting

Use the right-angle adapter to mount your Frontier XR+ on a ceiling, eave, or ledge by following these steps.

Attach the mounting plate to the mounting surface using the provided screws.
Attach the right-angle adapter to the back of the camera until it clicks.
Snap the right-angle adapter onto the mount until it clicks.
Adjust the camera's angle by gently swiveling it on the mount to aim at your target area.

When your camera is mounted, open the Blink app and create a thumbnail or enter live view to confirm the camera is aimed correctly. Adjust the angle as needed until you are satisfied with the field of view.

After mounting, visit your motion detection settings and activity zones in the Blink app to fine-tune your alerts and reduce unnecessary notifications.

Important: The Frontier XR+ is weather-resistant only when the back cover is securely fastened and the silicone plug covering the USB-C port is fully seated. After mounting, confirm the back cover sits flush with the camera and the silicone plug is in place.