Blink Video Doorbell (1st Gen) Wired Installation

If you wire your Video Doorbell (1st Gen) to compatible chime wiring, your in-home chime will sound for doorbell button presses. This article is an overview of the in-app process for wiring the Video Doorbell to your compatible chime system.

Note: Even when wired, the doorbell is always powered by size AA 1.5-volt lithium non-rechargeable batteries.

 Risk of electric shock. Disconnect power to the installation area at the fuse box or circuit breaker before beginning installation. If you aren’t comfortable with the processes and tools described in these steps, we recommend you hire a licensed professional.

Before you begin

Check your compatibility and voltage requirements

The Video Doorbell (1st Gen) requires a power supply between 16–24 VAC at 50/60 Hz and 40 VA maximum from your doorbell transformer. Ensure the voltage coming from the transformer matches the voltage of the chime. For example, a 16 V chime should be wired to a 16 V transformer. 

If your chime system provides less than 16 VAC, your doorbell will enter Event Response‍ mode.

If you’re unsure about your chime system’s voltage, visit How do I find my doorbell’s system voltage?

Delete

Turn off power to your existing chime system

Turn off power to the doorbell and chime box at your home’s circuit breaker.

 Risk of electric shock. Disconnect power to the installation area at the fuse box or circuit breaker before beginning installation. If you aren’t comfortable with the processes and tools described in these steps, we recommend you hire a licensed professional.
Delete

Remove your old doorbell

Unscrew and remove your old doorbell. Disconnect any wires attached to your old doorbell and remove any additional hardware.

Delete

Attach the back plate and connect the wires

Once you add the Video Doorbell (1st Gen) to your Blink account and select Mount with Wiring, the app will lead you through the wiring process.

  1. When you have the required items (Blink Video Doorbell kit, Power drill, and sticky tape), tap Continue to start your wired installation.

  2. Tap My transformer is compatible to confirm your doorbell transformer meets the 16–24 volts AC at 50/60 Hz and 40 VA maximum requirement and then tap Agree and Continue. If you’re unsure about your chime system’s voltage, visit How Do I Find My Doorbell’s System Voltage?

  3. If you haven’t turned off power to the doorbell and chime box, please do that now. When the power is off, tap Continue.

  4. If you haven’t removed your old doorbell, please do that now. Disconnect any wires attached to your old doorbell and remove any additional hardware.

  5. If you’re using a wedge or corner mount, visit Install a Wedge or Corner Mount for step-by-step instructions. If you’re not using a wedge or corner mount, move to the next step.

  6. Use the included template to show where the mounting holes are to be drilled. Tape the template in place, approximately 40 to 48 inches (102–122 cm) above the ground.

  7. Attach the back plate to your surface with the screws that are included. On a smooth surface, use the top and bottom holes. On an uneven surface, use the top and middle holes.

  8. Attach one doorbell wire to each screw on the back plate. Either wire can be connected to either post. Two extra screws are provided in the doorbell packaging.

Mount the doorbell

Use a two-step motion to attach the doorbell to the back plate. 

  1. Align the top edge of your doorbell to the back plate.

  2. Push it firmly against the back plate until you hear and feel a slight click to confirm it is secure. The doorbell can only be removed by inserting the release key at the bottom of it.
    • Note: If the ‘Wired power not supported’ alert message displays during wiring installation and your doorbell isn’t connected to a Sync Module, this means your existing chime wiring isn’t compatible. The doorbell will default to Event Response mode. Learn more about Event Response Mode.

Turn the power back on and complete your setup

Switch the power back on to your doorbell chime.

  1. The doorbell will search for a Wi-Fi connection and, when connected, you’ll see a confirmation message in the app.

  2. Next, select your chime type and tap Continue. If you are unsure which chime you have, visit Using the Video Doorbell With a Chime to learn more.

  3. After selecting a chime type, the app walks you through testing the sound of your chime. Learn more about changing the chime volume.

  4. If the connection is successful, tap Done and your Video Doorbell will be ready for use.


Can’t find what you’re looking for?

Contact Support